Powering Light

Lithium-Ion Batteries for Modern Illumination

High-Efficiency NCM Cells for Lighting Applications

Sr. No. Specifications Chemistry
1 3.7V 2Ah NMC
2 3.7V 2.2Ah NMC
3 3.7V 4.4Ah NMC
4 7.4V 2.2Ah NMC
5 7.4V 4.4Ah NMC
6 7.4V 4.4Ah NMC
7 11.1V 2.2Ah NMC
8 11.1V 2.5Ah NMC
9 11.1V 5Ah NMC
10 11.1V 7.5Ah NMC
11 14.8V 2.2Ah NMC
12 14.8V 2.5Ah NMC
13 14.8V 5Ah NMC

Lithium-ion batteries power modern lighting with high energy density and long life, making them ideal for compact, efficient, and long-lasting illumination.

Solar Panels

With efficiency, long runtime, and fast charging, lithium-ion batteries enhance safety and convenience in both emergency and everyday lighting.

Solar Panels

Built for Every Light

Compact Cells for Emergency, Portable and Outdoor Lighting

From a pocket torch to a street light, our NMC cells and packs give lighting products steady brightness, long runtime and quick recharging in a small body.

Emergency Lights

Switches on instantly during a power cut and holds charge while it waits in standby.

Torches and Lanterns

Light, rechargeable and easy to carry for home, travel and camping use.

Solar Garden and Street Lights

Stores daytime solar energy and powers LEDs through the night.

Work and Inspection Lights

Cordless lighting for workshops, repair jobs and field work, with no wire to trip over.

Pack Voltage Guide

Pack Voltage Cells in Series Typical Use
3.7 V 1 Torches, small LED lamps
7.4 V 2 Emergency lights, lanterns
11.1 V 3 Rechargeable bulbs, work lights
14.8 V 4 High-power LED and outdoor lights

Each cell is 3.7 V. Joining more cells in series raises the pack voltage. Higher Ah gives longer runtime.

Why Lighting Brands Choose Our Cells

  • Steady brightness: stable output so the light does not dim quickly as the battery drains.
  • Small and light: high energy density lets you design slimmer, easier-to-carry products.
  • Quick recharge: back to full sooner, ready for the next outage.
  • Custom packs: pick from the range in the table above, or ask us for a pack made to your size and voltage.

Know Your Runtime

How Long Will the Light Run?

Two numbers decide runtime: how much energy the pack stores and how much power your light uses.

The simple formula

Energy (Wh) = Voltage (V) × Capacity (Ah)

Runtime (hours) ≈ Energy (Wh) ÷ Light power (W)

Worked example

An 11.1 V, 5 Ah pack stores 11.1 × 5 = 55.5 Wh. A 10 W LED light drains it in about 55.5 ÷ 10 = 5.5 hours. Real runtime is slightly lower because of driver losses.

Pack Energy Runs a 10 W Light For
3.7 V 2 Ah7.4 Whabout 45 minutes
7.4 V 2.2 Ah16.3 Whabout 1.6 hours
7.4 V 4.4 Ah32.6 Whabout 3.3 hours
11.1 V 5 Ah55.5 Whabout 5.5 hours
11.1 V 7.5 Ah83.3 Whabout 8.3 hours
14.8 V 5 Ah74 Whabout 7.4 hours

Approximate figures. Actual runtime depends on your light's real power draw.

Safe by Design

Protection Built Into Every Pack

A battery management circuit watches the pack so your lighting product stays safe in daily use.

Overcharge protection

Stops charging when the pack is full, so the cells are not stressed.

Over-discharge protection

Cuts off the load before the battery drains too low and gets damaged.

Short-circuit protection

Disconnects the output quickly if a wiring fault shorts the terminals.

Cell balancing

In multi-cell packs, keeps cells at similar levels for even wear.

Protection features vary by pack. Ask us to confirm what is included in the model you need.

Get More From Your Battery

Charging and Care Tips

Do

  • Use a charger that matches the pack voltage.
  • Store in a cool, dry place away from direct sun.
  • Recharge unused emergency lights every few months so they stay ready.
  • Keep terminals and connectors clean and tight.

Avoid

  • Leaving the pack in a hot car or near a heater.
  • Using a swollen, dented or leaking battery. Stop using it and replace it.
  • Running it completely flat again and again.
  • Opening the pack or mixing cells of different types.

Got Questions?

Frequently Asked Questions

Can you make a custom pack for my light? +

Yes. Share the voltage, capacity, size limit and connector type you need, and we will suggest a pack built around them.

How do I choose between 7.4 V, 11.1 V and 14.8 V? +

Match the input voltage your LED driver expects. Then pick the Ah based on how many hours of light you need, using the runtime guide above.

What charger should I use? +

Use a lithium-ion charger rated for the pack's voltage. A 3-cell 11.1 V pack, for example, needs a charger made for 3-cell lithium-ion, not a lead-acid charger.

Can I use these batteries with solar lights? +

Yes, if the solar controller supports lithium-ion charging at the pack voltage. Tell us your controller model and we will confirm.

Do you supply in bulk for manufacturers? +

Yes. Send your monthly quantity and specifications and we will share availability and terms.

Need the Right Cell or Pack for Your Light?

Tell us your voltage, capacity and size needs. We will recommend a cell or build a custom pack.

Contact

Send Us a Message

WhatsApp